The MM74C922 CMOS key encoders provide all the necessary logic to fully encode an array of SPST switches. The keyboard scan can be implemented by either an external clock or external capacitor. These encoders also have on-chip pull-up devices which permit switches with up to 50 kΩ on resistance to b..
The 74HC04; 74HCT04 is a hex inverter. The inputs include clamp diodes that enable the use of current limiting resistors to interface inputs to voltages in excess of VCC.
Features:
Six Independent Invert Gates
Standard Pin Configuration
Also Available in SMD Type
Operating Tem..
The 74HC125; 74HCT125 is a quad buffer/line driver with 3-state outputs controlled by the output enable inputs (nOE).
A HIGH on nOE causes the outputs to assume a high impedance OFF-state. Inputs include clamp diodes.
This enables the use of current limiting resistors to interface inputs to ..
74HCT138 is a high-speed Si-gate CMOS device and is pin compatible with Low-power Schottky TTL (LSTTL).
74HCT138 decoder accepts three binary weighted address inputs (A0, A1 and A3) and when enabled, provides 8 mutually exclusive active LOW outputs (Y0 to Y7).
74HCT138 features three enable i..
The 74HC139; 74HCT139 decodes two binary weighted address inputs (nA0, nA1) to four mutually exclusive outputs (nY0 to nY3).
Each decoder features an enable input (nE).
When nE is HIGH all outputs are forced HIGH.
The enable input can be used as the data input for a 1-to-4 demultiplexer ..
The 74HC164; 74HCT164 is an 8-bit serial-in/parallel-out shift register.
The device features two serial data inputs (DSA and DSB), eight parallel data outputs (Q0 to Q7).
Data is entered serially through DSA or DSB and either input can be used as an active HIGH enable for data entry through..
The SN74HC244N is an Octal Buffer and Line Driver IC, designed specifically to improve both the performance and density of 3-state memory address drivers, clock drivers and bus-oriented receivers and transmitters.This device organized as two 4-bit buffers/drivers with separate output-enable (OE)/..
The 74HC245 is identical in pinout to the LS245.
The device inputs are compatible with standard CMOS outputs; with pull-up resistors, they are compatible with LSTTL outputs.
The HC245 is a 3-state noninverting transceiver that is used for 2-way asynchronous communication between data buses. ..
Features:
Identical to 74HC241 with Different Pinouts
Hysteresis at Inputs to Improve Noise Margin
PNP Inputs Reduce Loading
3-State Outputs Drive Bus Lines
Input Clamp Diodes
74HC541 3-STATE buffers utilize advanced silicon-gate CMOS technology. They possess high ..
The 74HC573; 74HCT573 is a high-speed Si-gate CMOS device and is pin compatible with Low-power Schottky TTL (LSTTL). It is specified in compliance with JEDEC standard no. 7A.
The 74HC573; 74HCT573 has octal D-type transparent latches featuring separate D-type inputs for each latch and 3-state t..
The 74HC595 is a very handy IC used in many microcontroller projects. You clock in 8 bits of data (like, on/off settings for 8 LEDs) via two lines, and when you toggle a third line, it pops these settings out on 8 outputs on the IC. So you trade 3 valuable lines on your microcontroller ..
Features:
Performs Comparison of Binary or BCD Codes
Can Compare Greater Than, Less Than and Equal
Words of Greater Length Can be Compared by Cascading
Operating Temperature up to 70oC
High-Speed CMOS Type
The 74HC/HCT85 are high-speed Si-gate CMOS devices and are pin compatible w..
Features:
Four Independent EXCLUSIVE-OR Gates
Standard Pin Arrangement
Fast Switching Times
Operating Temperature up to 70oC
High-Speed CMOS Type
The 74HC86 exclusive OR gate utilizes advanced silicon-gate CMOS technology to achieve operating speeds similar to equivalent LS-TTL ga..
Features:
Convert TTL Voltage Levels to MOS Levels.
High Sink-Current Capability.
Input Clamping Diodes Simplify System Design.
Open-Collector Driver for Indicator Lamps and Relays.
Inputs Fully Compatible With Most TTL Circuits.
These hex inverter buffers/drivers featur..
This device contains two independent positive-edge-triggered J-K flip-flops with complementary outputs.
The J and K data is accepted by the flip-flop on the rising edge of the clock pulse.
The triggering occurs at a voltage level and is not directly related to the transition time of the risi..
Features:
Designed specifically for high speed:
Memory decoders
Data transmission systems
DM74LS138 3-to-8-line decoders incorporates 3 enable inputs to simplify cascading and/or data reception
Schottky clamped for high performance
The DM74LS138 decodes one-..
Features:
Contains Two Multiplexers To Select Data Inputs Based on Data Select Inputs
Performs Parallel to Serial Conversion
Low Power
Operating Temperature up to 70oC
Standard TTL Switching Voltages
Each of these data selectors/multiplexers contains inverters and drivers to suppl..
Features:
Single 8-bit Shift Register with Gated Serial Inputs and Asynchronous Clear
Fully Buffered Clock
Clock Frequency up to 36MHz
Operating Temperature up to 70oC
Standard TTL Switching Voltages
General Description:
These 8-bit shift registers feature gated serial inputs a..
Features:
Parallel Inputs and Outputs
Four Operating Modes, Synchronous, Right Shift, Left Shift and Pause
High Speed up to 25MHz
Positive Edge Triggered Clocking
Standard TTL Switching Voltages
General Description:
This bidirectional shift register is designed to incorporate..
Features:
Four Independent OR Gates
Standard Pin Configuration
Fast Switching Times
Operating Temperature up to 70oC
Standard TTL Switching Voltages
General Description:
This device contains three independent gates each of which performs the logic OR fucntion.
..
Features:
Accepts Four Line of BCD Input and Converts this to Seven Open Collector Outputs
Open Collector Outputs require Pull-Up Resistors
Lamp Test Input
Operating Temperature up to 70oC
Standard TTL Switching Voltages
General Description:
The 74LS47 accepts four lines of BCD..