DESCRIPTION:
This is essentially a ramped up version of our Ardumoto motor driver shield. For this monster shield we've replaced the L298 H-bridge with a pair of VNH2SP30 full-bridge motor drivers. We've also beefed up the support circuitry so this board is capable of driving a pair of high-curre..
DESCRIPTION:
Brand new and high quality.
Input voltage range: 3.5V-30V (output set voltage higher than the input voltage must be guaranteed)
Output voltage range: 4.0V-30V
Input maximum current: 5A (based on power conservation under nominal conditions the output current Uin * Iin *..
PRODUCT DESCRIPTION:
When you use the product, the module inputs and outputs to be isolated from ground!
Input voltage range:4~38VDC(Note:input voltage not exceeding 38V)
Output voltage range:1.25-36VDC adjustable
Output current: 0-5A
Output power: 75W
High efficiency up to ..
DESCRIPTION:
DIY Mobile Power Supply, 5V output for charging Phone, MP3, MP4, PSP, etc
Modules nature: non-isolated Buck
With Overcurrent Protection
Rectification: Non-synchronous rectification
(Note: Please connect right as the printed : N-,IN+,OUT-,OUT+ ,or else the Module will be bu..
Special Note:
This part of the DC power module buck power supply module , the input voltage should always be greater than the output voltage and must have at least 1V differential input power = output power + losses (energy conservation principle)
200W DC-DC high voltage synch..
DESCRIPTION:
super current carrying capacity (maximum 8 A), to provide the strong power to your device!
Tight layout, limited space for you to make the biggest concessions
Additional radiator, no longer worry about equipment and higher temperature
SCOPE OF APPLICATION:
Can be us..
DESCRIPTION:
Step Down Module
Condition: New
With temperature protection, over current protection and short circuit protection, high and low voltage isolation, AC85 ~ 265 v wide voltage input, ac/dc current , 431 precision voltage stability DC5V output
Input voltage: AC 85 ~ 265 v 50/6..
Performance and highlights:
Voltmeter wide range DC4.5 ~ 40V.
5V/2A output current (Only when the input voltage is 6.5 ~ 40V, it can output 5V).
A key ("Output Enable" button) switch USB output, a key ("low-power" button) to enter the ultra-low power.
Voltmeter can be artificial..
DESCRIPTION:
100% brand new and high quality
Use a dedicated benchmark IC, and high-precision current sensing resistor,
High output current, the max output current can reach 9A.
Low output ripple , high frequency capacitor reduces output ripple.
Suitable for LED driver.
SPECIFIC..
DESCRIPTION:
DSN6009 4A is a high-performance step-up switching current (BOOST) module. The module uses the second generation of high-frequency switching technology XL6009E1 core chip performance than the first generation technology LM2577. XL6009 boost module at a lower cost. superior performanc..
Product description:
LM2596 LM2596S ADJ POWER SUPPLY DC-DC STEPDOWN module 5V/12V/24V adjustable Voltage regulator 3A
DIY mobile power supply, car power, communications equipment power supply, etc.
..
DESCRIPTION:
100% Brand New and High Quality
The TB6612FNG motor driver can control up to two DC motors at a constant current of 1.2A (3.2A peak).
Two input signals (IN1 and IN2) can be used to control the motor in one of four function modes - CW, CCW, short-brake, and stop.
The two mo..
DESCRIPTION:
A4988 is a complete microstepping motor driver with built-in translator for easy operation. This product is available in full, half, 1/4, 1/8 and 1/16 step modes operate bipolar stepper motors, output drive capacity of up to 35 V and ± 2 A. A4988 includes a fixed off-time current reg..
FEATURES:
1.2 HG7881 chip on board motor control.
2.The module can simultaneously drive two DC motors or a 4-wire two-phase stepper motor.
3.The module input voltage: 2.5-12V
4.Each channel has a 800mA continuous output current capability.
5.PCB dimensions: &nb..
DESCRIPTION:
HLK-5M03 from Hi Link is a isolated power supply module with input range of 100 volt to 240 volt AC and output of DC 3.3 volt and power rating of 5 watt. Its ultra compact size makes it perfect to use in places where size is a constraint. It is a compact PCB ..
DESCRIPTION:
HLK-5M05 from Hi Link is a isolated power supply module with input range of 100 volt to 240 volt AC and output of DC 5 volt and power rating of 5 watt. Its ultra compact size makes it perfect to use in places where size is a constraint. It is a compact PCB mo..
DESCRIPTION:
HLK-5M12 from Hi Link is a isolated power supply module with input range of 100 volt to 240 volt AC and output of DC 12 volt and power rating of 5 watt. Its ultra compact size makes it perfect to use in places where size is a constraint. It is a compact PCB m..
DESCRIPTION:
This is a rather small module that can supply 5V/0.6A from either 120VAC or 230VAC, this makes it perfect for small projects that needs a 5 volt supply from mains.
SPECIFICATIONS:
Meet UL, CE requirements,
All voltage input (AC: 90 ~ 264V)
Low ripple and low noise
Outp..