DESCRIPTION:
A DC motor with gear box attached to the shaft, which is mechanically commutated electric motor powered from direct current (DC). Generally used in DIY projects, Battery operated toys, Radio controlled vehicles, Robotic projects etc.
SPECIFICATIONS:
RPM: 100
Oper..
DESCRIPTION:
12V DC geared motors for robotics applications. Very easy to use and available in standard size. Nut and threads on shaft to easily connect and internal threaded shaft for easily connecting it to wheel.
FEATURES:
12V DC motors with Gearbox
6 mm shaft diameter with int..
SPECIFICATION:
Stainless steel sheath and waterproof
Measurement range: -20 to 105 C
Length of wire:1 meter
Size of probe: 5 x 25 mm
Output 2 wires
Type: NTC 10k 1% 3950
measure environmental temperatures using arduino ADC and this 10k NTC LINK
Resistance to temperature conversio..
FEATURES:
Peak Repet. Reverse Voltage (Vrrm): 1000V
Average Rectified Current (Io): 3.0A
Max. Reverse Current (Ir): 0.5mA
Max. Forward Voltage Drop (Vf): 1.2V
..
DESCRIPTION:
2.4G 2DBI RP SMA Male Antenna Interface WIFI wireless 109MM long omnidirectional antenna
Name: 2.4GHzAntenna
Scope: IEEE802.11 b/g/n WLAN System
Wireless Communication System
Wi-Fi / WiMAX / MIMO System
S.W.R <= ..
FEATURES:
2.4GHz antenna
RP-SMA connector
Gain 3.0 dBi
This antenna is 8x50mm with 40mm black rubber antenna. It can be used with the WIFI Master Extension and is equipped with a male RP-SMA connector (no pin).
..
DESCRIPTION:
Fingerprint scanners are awesome. use a key when you have one right at the tip of your finger? Unfortunately, they're usually unreliable or difficult to implement. Well not anymore! We've found this great fingerprint module from ADH-Tech that communicates over TTL Serial so you..
DESCRIPTION:
Raspberry Pi comes with HDMI Port and does not have VGA port to connect to conventional PC monitor. This converter helps in using the existing monitors as display for Raspberry Pi.
You can connect any VGA Monitor (including old CRT Monitors) to Raspberry Pi using HDMI to VGA..
BASIC WORKING PRINCIPLE:
1. Using IO port TRIG trigger location, to the high level signal of at least 10us;
2. Module automatically sends 8 40KHz Fang Bo, automatic detecting whether a signal return;
3. A signal return, a high level is output through the IO port ECHO, the tim..
DESCRIPTION:
Gear Type: All Metal Gears
Stall torque: 12kg / cm (6V)
Power Supply: Through External Adapter
Operation Voltage: 4.8 - 7.2 V
Temperature range: 0 to 55
Operating Speed: 0.17sec / 60 degrees (4.8V no load)
Operating Speed: 0.13sec / 60 degrees (6.0V no load)
Complian..
DESCRIPTION:
This RF adapter cable is super handy for anyone doing RF work. Often times, small electronics save space by having a pick-and-placeable u.FL connector (also called uFL, IPEX, IPAX, IPX, MHF, and AM). But most antennas have SMA or RP-SMA connectors on them. This little cable will brid..
DESCRIPTION:
Brand New and High Quality
Excellent for Raspberry PI
PL-2303HX USB to Serial Controller adopted
Approximately 1m long cable
4 connecting wires, 2.54mm pitch type.red= 5V , black= GND , white= RXD , green= TXD
Supports baud rate from 75 to 128000
Support Win 98 o..
DESCRIPTION:
NFC Chip Type: NTAG203
full compliance with NFC Forum Tag Type 2 specifications
168 bytes of shared memory 42 is divided into pages (four bytes each)
144 bytes of user R / W memory area 36 is divided into pages (four bytes each)
Rewrite Endurance: 10,000 cycles
16-bit co..
SPECIFICATION:
Official NFC tag chips: NTAG216
Chip effective capacity: 888 bytes
It supports read count, UID ASCII mapping
Appearance Material: PP waterproof synthetic paper, a pattern can be customized
Label Diameter: 23mm (smaller than a coin!)
Mobile Access distance: > 3cm
E..
DESCRIPTION:
Gold-plated machined brass construction
Gold-plated contacts - teflon insulator
Great for wireless router, access point repair or similar projects
Connect high gain IPX to SMA
SPECIFICATION:
Connector: IPX IPEX to RP-SMA female jack(center male pin)
Cable type: 1.13 U.FL
L..